Tour

Start at first visit (openStart)

This constraint allows you to indicate whether the resource starts their route at the first visit or at the address indicated as their geolocalised address.

If the value is set to Disabled, the cost of the route is calculated from the localisation of the resource.
If the value is set to Enabled, the cost of the route is calculated from the first visit.

The default value is Disabled.

If the value of the First stop at depot constraint is Enabled, the cost calculated starts at the site where loading is to take place.

End at last visit (openStop)

This constraint allows you to indicate whether the resource finishes their route at the last visit or at the address indicated for the resource’s geolocalisation.

If the button is set to Disabled, the cost of the route is calculated up until the resource’s return to geolocalisation address.
If the button is set to Enabled, the cost of the route is calculated up until the resource’s return to the last visit.

The default value is Disabled.

If the value of the Last stop at depot constraint is Enabled, the cost calculated finished at the site where reloading is to take place.

tscloud-img/tourneelibre.png

Example 1: Start at first visit = Disabled and End at last visit = Disabled

The journey time of this route is 3h20 (1h+20m+30m+1h30)and distance is 250kms (70+30+50+100).

Example 2: Start at first visit = Enabled and End at last visit = Enabled

The journey time of this route is 50 minutes (20m+30m) and distance is 80kms (30+50).

It is possible to dissociate the start and end constraints.

Measure distance from first visit

This constraint allows you to count or not in the optimisation the distance between the resource start location and the first visit (resource location or start point if is defined).

Format: binary

If the value is set to Disabled, the cost km of the route is calculated from the localisation of the resource.
If the value is set to Enabled, the cost km of the route is calculated from the first visit.
The default value is Disabled.

[Warning] Warning

If the value of the First stop at depot constraint is Enabled, the cost km calculated starts at the site where loading is to take place.
If the value of the Briefing duration is used, the cost km calculated starts at the stop following the briefing.
If the value of the Start at first visit constraint is Enabled, this constraint is disabled.

Stop distance measurement at last visit

This constraint allows you to count or not in the optimisation the distance between the last visit and resource stop (resource location or stop point if is defined).

Format: binary

If the value is set to Disabled, the cost km of the route is calculated up until the resource’s return to geolocalisation address.
If the value is set to Enabled, the cost km of the route is calculated up until the resource’s return to the last visit.
The default value is Disabled.

[Warning] Warning

If the value of the Last stop at depot constraint is Enabled, the cost km calculated stops at the site where reloading is to take place.
If the value of the Debriefing duration is used, the cost km calculated stops at the stop preceding the debriefing.
If the value of the End at last visit constraint is Enabled, this constraint is disabled.

Measure time from first visit

This constraint allows you to count or not in the optimisation the time between the resource start location and the first visit (resource location or start point if is defined).

Format: binary

If the value is set to Disabled, the hourly cost of the route is calculated from the localisation of the resource.
If the value is set to Enabled, the hourly cost of the route is calculated from the first visit.
The default value is Disabled.

[Warning] Warning

If the value of the First stop at depot constraint is Enabled, the hourly cost calculated starts at the site where loading is to take place.
If the value of the Briefing duration is used, the hourly cost calculated starts at the stop following the briefing.
If the value of the Start at first visit constraint is Enabled, this constraint is disabled.

Stop time measurement at last visit

This constraint allows you to count or not in the optimisation the time between the last visit and resource stop (resource location or stop point if is defined).

Format: binary

If the value is set to Disabled, the hourly cost of the route is calculated up until the resource’s return to geolocalisation address.
If the value is set to Enabled, the hourly cost of the route is calculated up until the resource’s return to the last visit.
The default value is Disabled.

[Warning] Warning

If the value of the Last stop at depot constraint is Enabled, the hourly cost calculated stops at the site where reloading is to take place.
If the value of the Debriefing duration is used, the hourly cost calculated stops at the stop preceding the debriefing.
If the value of the End at last visit constraint is Enabled, this constraint is disabled.

tscloud-img/tourneelibre.png

Example 1: Open time start and stop = Disabled and Open distance start and stop = Enabled

The journey time of this route is 3h20 (1h+20m+30m+1h30)and distance is 80kms (30+50).

Example 2: Open time start and stop = Enabled and Open distance start and stop = Disabled

The journey time of this route is 50 minutes (20m+30m)and distance is 250kms (70+30+50+100).

Maximum daily distance (maximumDistance)

This constraint allows you to define the maximum distance a resource may travel in one working day.

Format: number

Maximum visits per day (maximumVisits)

This constraint designates the maximum number of visits a resource can perform during one working day.

Format: number

Prev  Up  Next
  Home